Attention: the Quickstart Guide for BSP 2.8, based on the Ångström distribution, is not being updated anymore. Depending on your SoM, you have different options:

Vybrid and Tegra: the information is provided as-is and still accurate, since newer Toradex BSPs are not ported to those SoMs. Just keep in mind that the Guides are not being maintained anymore, even if we find bugs or outdated instructions.

Apalis TK1 (all variants), Colibri iMX6ULL (all variants), Colibri iMX7S 256MB and Colibri iMX7D 512MB: these computer on modules are still regularly maintained in our BSPs and, to get started, you must check the software page Toradex BSP Layers and Reference Images for Yocto Project. Since Torizon is not supported, at the moment a Quickstart Guide is not available.

All other i.MX-based SoMs: you have two options to get started with embedded Linux: the first is to follow the Quickstart Guide for Torizon, which provides the greatest out-of-the-box experience, or if you choose to use Yocto, check the software page Toradex BSP Layers and Reference Images for Yocto Project.

Overview

In this how-to section, you will update to the latest pre-built Linux image provided by Toradex.

In this module you will:

Format an SD card.
Use an SD card to flash the new image to the module.
Access the Eboot bootloader and replace it with the U-Boot bootloader.
Flash a new Linux image to the module.

Prerequisites

The following table lists the items required:

List of items required
Micro SD card with more than 2GB

Note: The following steps are meant to be run in the development workstation, and not on the target module, unless otherwise stated. Note: Whenever there is a reference to SD card, it means the micro SD card plus an adapter connected to the host machine, unless otherwise noted.

Step 1

Install the prerequisites for generating the SD card:

sudo dpkg --add-architecture i386
sudo apt-get update
sudo apt-get install dosfstools e2fsprogs gawk mtools parted
sudo apt-get install zlib1g:i386 liblzo2-2:i386 libuuid1:i386 libusb-1.0-0:i386
sudo apt-get install gparted

Step 2

Before inserting the SD card in your host computer, list the hard-disks and partitions being used by your system. See the example below:

user@host:~$ df -h
Filesystem      Size  Used Avail Use% Mounted on
udev            3,9G     0  3,9G   0% /dev
tmpfs           792M   50M  743M   7% /run
/dev/sda7        42G   30G   10G  75% /
tmpfs           3,9G  145M  3,8G   4% /dev/shm
tmpfs           5,0M  8,0K  5,0M   1% /run/lock
tmpfs           3,9G     0  3,9G   0% /sys/fs/cgroup
/dev/sda5       922M  340M  520M  40% /boot
/dev/sda8       178G   28G  141G  17% /usr/local
/dev/sdb5       620G  558G   31G  95% /home
tmpfs           792M   92K  792M   1% /run/user/1000

Notice that there are two hard-disks: /dev/sda and /dev/sdb. The indexes list different partitions inside the disks and can be ignored.

Step 3

Insert the SD card in the host computer. A pop-up message should appear. Select the option Do Nothing, as illustrated in the picture below:

Select *do nothing* after SD card insertion

Notice that some SD cards have a physical lock that enables read-only mode, therefore you have to make sure this lock is not enabled. If the lock is enabled, further steps from this how-to section will not work.

Step 4

List the hard-disks and partitions being used by your system. See the example below:

user@host:~$ df -h
Filesystem      Size  Used Avail Use% Mounted on
udev            3,9G     0  3,9G   0% /dev
tmpfs           792M   50M  743M   7% /run
/dev/sda7        42G   30G   10G  75% /
tmpfs           3,9G  145M  3,8G   4% /dev/shm
tmpfs           5,0M  8,0K  5,0M   1% /run/lock
tmpfs           3,9G     0  3,9G   0% /sys/fs/cgroup
/dev/sda5       922M  340M  520M  40% /boot
/dev/sda8       178G   28G  141G  17% /usr/local
/dev/sdb5       620G  558G   31G  95% /home
tmpfs           792M   92K  792M   1% /run/user/1000
/dev/mmcblk0p1  7,5G  296M  7,2G   4% /media/<user>/3E18-AADE

Notice that there is a new device, /dev/mmcblk0, and this is the SD card.

If you use an SD card to USB adapter, your device may be listed as /dev/sdX, being X a character that depends on how many disks your system have. For the computer from the exemple, the device is /dev/sdc:

/dev/sdc1       7,5G  296M  7,2G   4% /media/<user>/3E18-AADE

Attention: Proceed carefully through the next steps. If you use the wrong device, you will erase the computer hard-disk and permanently lose data.

Step 5

Note: The following steps assume the SD card is listed as /dev/mmcblk0. Please adjust the instructions accordingly.

Warning: Backup your SD card data. The SD card will be formatted and all data will be lost.

Start gparted from command-line using the SD card device as an argument:

sudo gparted /dev/mmcblk0

A window such as presented in the figure below will open. In the top-right corner of the window, only the SD card device must be listed:

Gparted GUI

Warning: If you do not pass the SD card as an argument to gparted, all your drives will be listed and, therefore, you are more prone to formatting your machine's HD.

Step 6

From the Partition menu, select the Unmount option:

Unmount the SD card

Step 7

Delete all of the partitions from the SD card, by using the option Delete from the menu Partition:

Delete the current SD card partitions

Step 8

From the Partition menu, select the New option. A new window will appear:

Create new partition

Step 9

From the File system drop-down menu, select the fat32 option:

Select FAT32 file system

Also create a label for your partition, such as data. This is not mandatory, but when the system automatically mounts the SD card, it will use this label as the name of the directory where the device will be mounted.

Step 10

Start the process by clicking the green check button Apply All operations, and acknowledge the warning message:

Apply all operations

Acknowledge warning message

A window will display information during the process. Just wait until it finishes:

Formatting SD card

In the end, you must have a Gparted window such as the one below. You can then close Gparted.

SD card successfully formatted

Step 11

Mount the SD card. Two easy ways of doing it are: - Either to click the SD card icon in the launcher to the left of the screen, or - Open the files manager and click the SD card partition label listed at the left side of the window.

Both options are illustrated in the figure below:

Mount the SD card

Notice that the default mount path for Ubuntu is:

/media/<user>/<partition_label>

Where user is the user you are logged in, and partition_label is the label chosen at step 10, or a random alphanumeric value if the label was left blank.

Step 12

Download the pre-built Linux image. Find the latest Toradex pre-built image for your module here.

Note: Due to the limited amount of RAM available on Colibri VF50, the full LXDE demo image simply won't fit. Please use the console-tdx-image aka Colibri-VF_Console-Image instead.

Step 13

Extract the compressed file contents with root privileges:

Note: You must execute as root to preserve the target root filesystem permissions.

sudo tar xjvf Colibri-VF_LXDE-Image_<bsp-version>-<date>.tar.bz2

Step 14

To flash the SD card, enter the Linux image directory and run the update.sh script:

cd Colibri-VF_LXDE-Image_<bsp-version>
./update.sh -o /media/<user>/<partition_label>/

Step 15

Unmount the SD card and remove it from the development workstation:

umount /media/<user>/<partition_label>/

Step 16

Insert the micro SD card in the SD/MMC connector, as illustrated. Notice that for this step, the SD/USB adapter is not required:

Micro SD card slot highlighted

Step 17

Make sure that you have a working serial terminal application on your host PC.

Note: You can go back to the last section if there are any doubts regarding the serial terminal application and its configuration.

On your PC, select your terminal application to get the focus. Press the SPACE key and keep it pressed while turning on the Toradex system.
This procedure will stop the bootloader and you will see the following text in the terminal application:

Toradex Bootloader 1.1 BETA 2 for Colibri Built Apr 28 2015
CPU: MVF61 500 Mhz
Flash: 512 MB
RAM: 256 MB
Using ECC Type: 7
Booting from fuses.
Colibri VF61 module version 1.2A
Press [SPACE] to enter Bootloader Menu
Initiating image launch in 1 seconds.
BootLoader Configuration:
C) Clear Flash Registry
X) Enter CommandPrompt Mode
D) Download image to RAM now
F) Download image to FLASH now
L) Launch existing flash resident image now
Enter your selection:

Note: If you press the SPACE key too late, the system will start booting. Power-off and try again.

Step 18

Press X to enter the CommandPrompt mode, then enter flashloader colibri_vf/u-boot-nand.imx to flash U-Boot:

...
Enter your selection: x
>flashloader colibri_vf/u-boot-nand.imx
Bootloader image size: 424728 bytes.
Loading done.
Flashing bootloader.
Writing 208 sector(s) of bootloader code from sector 64.
Erasing block 1
................................................................
Erasing block 2
................................................................
Erasing block 3
................................................................
Erasing block 4
................
Flashing completed.

Step 19

Enter reboot or power-cycle the board, immediately pressing any key to prevent the system from booting.

>reboot

Note: If you press any key too late, the system will start booting. Power-off and try again.

Step 20

To finish updating the system, run the commands:

nand erase.part ubi
run setupdate
run update

Updating the module

After a while, the system will boot with the updated Linux image and you will see the login message:

Login to the Linux terminal

Step 21

If you are new to Linux or the command-line interface and want to learn some basic commands, please read this article

Back

Back to Overview